This program should cut out an outline, a few letters, and then a rectangular
border, resulting in a metal postcard about 6" wide (X dir) by 5" high (Y dir).

Set the zero point of the drill tip at the bottom-left corner of the rectangle
that will be printed, leaving room for the machine to draw 6" in the positive X
and Y directions. I *think* it had room for 6 inches, it says in the manual what
the box size is. I *think* it was 6"x8" but I could be way off.

I'm reusing as many settings as possible from the D-SUB cutting program.

START MM  02 // Use millimeters. Program ID 01 is taken by the D-SUB program I think.
 TD=   3.175 // Tool diameter: 1/8 in = 3.175 mm
FR XY  =03.7 // Divided the suggested feedrate by two, because tool was flexing.
FR Z   =01.2 // Feedrate based on 1 cutting edge, instead of 4, then slightly reduced.
SETUP >zcxyu // Allow user to position tool above bottom-left corner.
Z>C          // Raise tool
GOfX   8.500 // Point 1 of Figure 1
GOfY 121.000 //
GO Z-  9.000 // Insert tool
GO X   8.000 // Point 2 
   Y 119.000 //
GO X   9.000 // Point 3
   Y 110.500 //
GO X   6.500 // Point 4
   Y 100.500 //
GO X  12.500 // Point 5
   Y  92.500 //
GO X  13.500 // Point 6
   Y  83.500 //
GO X  25.000 // Point 7
   Y  70.500 //
GO X  25.500 // Point 8
   Y  64.300 //
GO X  28.000 // Point 9
   Y  60.500 //
GO X  30.000 // Point 10
   Y  60.500 //
GO X  32.000 // Point 11
   Y  57.500 //
GO X  30.000 // Point 12
   Y  55.000 //
GO X  31.000 // Point 13
   Y  51.500 //
GO X  43.500 // Point 14
   Y  31.000 //
GO X  53.000 // Point 15
   Y  30.000 //
GO X  63.000 // Point 16
   Y  25.500 //
GO X  74.000 // Point 17
   Y  16.000 //   
GO X  76.500 // Point 18
   Y   9.000 //   
GO X 100.000 // Point 19
   Y  11.000 //   
GO X  99.500 // Point 20
   Y  21.000 //   
GO X 103.500 // Point 21
   Y  28.000 //   
GO X  99.000 // Point 22
   Y  36.000 //   
GO X  47.500 // Point 23
   Y  83.500 //   
GO X  47.500 // Point 24
   Y 121.000 //   
GO X   8.500 // Return to Point 1
   Y 121.000 //
Z>C          // Raise tool
GOfX  78.000 // Point 1 of Figure 2
GOfY 103.500 //
GO Z-  9.000 // Insert tool
GO Y  73.000 // Point 2
GO Y  89.000 // Point 3 
GO X  98.000 // Point 4 
GO Y 103.500 // Point 5
GO Y  73.000 // Point 6
Z>C          // Raise tool
GOfX 110.000 // Point 1 of Figure 3
GO Z-  9.000 // Insert tool
GO Y  85.000 // Point 2 of Figure 3
Z>C          // Raise tool
GOfY  92.000 // Point 3 
GO Z-  9.000 // Insert tool
Z>C          // Raise tool
GOfX 124.500 // Point 1 of Figure 4
GOfY  73.000 //
GO Z-  9.000 // Insert tool
Z>C          // Raise tool
GOfY  79.000 // Point 2 of Figure 4
GO Z-  9.000 // Insert tool
GO Y 100.000 // Point 3 of Figure 4
Z>C          // Raise tool
GOfX   0.000 // Return home
GOfY   0.000 //
GO Z-  9.000 // Insert tool
GO X 144.000 // Point 2 of border
GO Y 126.000 // Point 3 of border
GO X   0.000 // Point 4 of border
GO Y   0.000 // Return home.
Z>C          // Raise tool
END NEW PART //